Book Services

 

 

The content following next about A Step-by-Step Guide to Installing a Bathtub is unquestionably motivating. Don't miss it.

Mounting a tub isn't precisely rocket science, but it does call for strong plumbing, woodworking, and sometimes, tiling skills. Changing an old tub with a new one is also a reasonably hard job. If the old tub is conveniently easily accessible, the job can move speedily; if you need to open a wall surface to remove the old bathtub and also place the brand-new bath tub, the job is much harder. In either case, the task is within a house handyman's skills, although you will certainly require a helper to vacate the old bathtub as well as set in the new one. Ensure you have actually qualified yourself for the work as well as are comfortable trying it. Instead of employing a specialist to take over a halfway-completed task, it is better to take into consideration employing one prior to you begin. Opportunities are you might need a specialist plumber to make tube connections.
This write-up will help you set up a new bath tub in your bathroom if you have actually already gotten a new tub as well as do not need to transform the arrangement of your previous water pipes.
Your devices and also product checklist must consist of the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipe Caps


 

Getting ready for the Installation

First of all, the supporting framework provided with the bath needs to be fitted (if required) according to the maker's instructions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is very important to make sure that if the tap features a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps device to prevent stress on the bath tub.
Fit the flexible tap adapters to the bottom of both taps utilizing 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet via the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you make use of every one of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath ought to now be ready to be fitted in its final setting.

 

 

Removing Old Touches

If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you should do is detach the water system. After doing so, switch on the faucets to drain pipes any kind of water continuing to be in the system. The process of removing the existing taps can be quite problematic because of the restricted gain access to that is commonly the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the faucets. Have a fabric prepared for the remaining water that will originate from the pipelines. When the supply pipes have been removed, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from transforming throughout this process. Once the taps have actually been eliminated, the holes in the bath/basin will have to be cleansed of any kind of old sealing compound.
Prior to going on to fit the brand-new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.

 

 

Installing the Bath tub

Making use of the two wooden boards under its feet, position the tub in the called for placement. The wood boards are helpful in equally spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 small factors.
The next objective is to guarantee that the bath tub is leveled all round. This can be accomplished by checking the level as well as adjusting the feet on the tub until the level reviews degree.
To set up taps, fit all-time low of the furthest flexible faucet port to the suitable supply pipe by making a compression sign up with; then do the same for the various other tap.
Switch on the water as well as check all joints and also brand-new pipework for leaks and also tighten them if required. Fill the bath tub and also inspect the overflow outlet and also the typical outlet for leakages.
Finally, deal with the bath paneling as described in the maker's instruction manual. Tiling and also sealing around the bath tub must wait until the bath tub has been made use of a minimum of when as this will resolve it into its last setting.

 

 

Suitable New Taps

If the tails of the brand-new taps are plastic, after that you will need a plastic adapter to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet and also the other end supplies a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the mounting opening in the bath/basin making certain that the washers are in area in between the tap as well as the sink. Safeguard the faucet in position with the supplier provided backnut. When the faucet is firmly in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical faucet adapters. The former type ought to be attached to the faucet ends first, tightening only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.

 

 

Tiling Around the Bathtub

In the area where the bathroom satisfies the floor tile, it is essential to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to crack a stiff seal, triggering the water to permeate the wall surface in between the bathroom and also the tiling, bring about difficulties with moisture as well as feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components and also installations. They are marketed in tubes and also cartridges, and also can sealing spaces as much as a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to constantly fill up the tub with water before securing, to permit the activity experienced when the bathtub remains in usage. The sealant can break relatively early if you do not consider this movement before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise easily available on the market. It is advisable to fit the tiles using water-resistant or waterproof sticky and grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

We hope you enjoyed reading our article on A Step-by-Step Guide to Installing a Bathtub. Thanks a lot for taking the time to read through our content. Loved our piece of writing? Please share it. Let somebody else find it. Thank-you for your time invested reading it.

Click Here To Read More